Does Linksys Velop not working, Linksys Velop red light, and Linksys Nodes not connecting, bring worry to you? Fret not! This Linksys Velop troubleshooting guide will help you put an end to all your Linksys Velop Setup issues. By suggesting ways to resolve the most common Linksys Velop errors, this guide will help you ensure lag-free internet connectivity at your place 24/7.
Linksys Velop is among the most sought-after mesh type home WiFi systems. Features like steadfast internet connectivity paired with superior network performance and more, are some reasons why you should buy one too. However, due to certain situations beyond your control, the device may develop issues, which might hamper your internet browsing experience. Good news is, these issues can be resolved. How? We’ll discover in this article right below.
Common Linksys Velop Issues you may face
- Linksys Velop Not Working
- Linksys Velop Setup Issues
- No Internet on your Linksys Velop
- Linksys Velop Red Light
- Linksys Velop Nodes Not Connecting
Apart from the Linksys Velop issues listed above, there can be issues related to slow internet speeds, frequent internet disconnections, speed throttling issues and more. However, once you start following the steps mentioned in this article, you’ll notice the difference immediately through increased router performance and wireless coverage.
Reasons behind Linksys Velop Setup Issues
There may be several reasons that might trigger issues with your Linksys Velop Mesh router. These can vary from power connectivity issues, to wireless interference, excessive distance from the main router, outdated firmware, device hardware issues, and overutilization of the available network bandwidth. Before you proceed with the Linksys Velop troubleshooting steps, you will need to analyse what’s causing the issue. This will help you define the next course of action and take remedial steps to reach a resolution.
Proven Linksys Velop Troubleshooting Steps
Basic checks you can perform
Before you move on to the troubleshooting part, you’ll need to check if the essential elements of your network topology are functioning well. These include the power supply, the condition of the equipment used and network.
- Check the power supply to ensure that the Linksys Velop system setup is operating at nominal voltage. If your area suffers voltage fluctuations, it is a good idea to use a stabiliser.
- Inspect the condition of the ethernet cables and power cables that are in the network topology. Ensure that they are in the most immaculate condition and there is no sign of wear and tear. If you find any such signs, replace the cables with new ones.
- Ensure that the hardware of your Linksys Velop system setup is installed properly. Check the antennas and other cable connections to confirm that everything is in the right shape.
Once you have checked the above, you can follow the Linksys Velop troubleshooting guide as described below.
How to troubleshoot Linksys Velop issues?
There are several Linksys Velop Troubleshooting steps you can follow when looking to resolve issues. Below are some of them:
- Power cycle your Linksys Velop Router
- Change the power and network cables
- Relocate your Linksys Velop Router
- Update firmware version
- Disconnect unnecessary devices
- Change WiFi Channel
- Perform a Factory Reset
Power cycle your Linksys Velop Router
The very first step in troubleshooting Linksys Velop router issues is to power cycle the velop mesh system. Doing so can help remove a lot of issues, especially related to hardware and network performance. Also, power cycling your router can help reset the device network activity which in turn will benefit you.
- To power cycle your Linksys router, simply turn it off and unplug the power adapter from the power outlet.
- Allow the velop to remain in this state for about 30 seconds and then reboot.
- Check if the issue is still there.
Change the power and network cables
If your Linksys Velop router has not been functioning well, this Linksys Velop troubleshooting guide can help you reach a resolution. Damaged power and network cables can affect network connectivity and device performance. It is always a good idea to replace the damaged cables since they may also cause short circuits in unsuitable conditions.
If the cables aren’t damaged, yet you are facing issues with your Velop, try checking the cable connections. Ensure that the cables are connected securely to the devices.
Relocate your Linksys Velop Router
If your Linksys Velop Node keeps going offline, there may be issues with the WiFi connectivity. Check if there is an obstruction in between the main router and the Velop node. If so, remove the same and establish a line of sight connection between them. Furthermore, if you are still getting the Linksys Velop Node not connecting issue, try moving your Linksys Velop router closer to the Velop node. Find the optimum location where the signal quality is the best and then try again.
Update Firmware Version
A lot of Linksys Velop router issues can arise due to outdated firmware versions. It is a good idea to enable the automatic firmware update option. If you still wish to update the firmware manually, you can download the latest firmware file from the official website and upload the same to your device through the web-based Linksys Velop system setup wizard.
Disconnect unnecessary devices
If there are too many devices connected to your Linksys Velop router, you may face Linksys Velop speed issues, or speed throttling issues. This will hamper your web surfing experience and deteriorate your internet performance. It is a good idea to disconnect the extra devices from the router network and only connect those that you actually need.
Also, try changing the network password regularly to ensure that hackers and unauthorised people cannot access it.
Change WiFi Channel
Check which WiFi channel you are connected to. If the WiFi channel is overcrowded, you can shift to the other channel so you don’t face issues like internet disconnections and more. It is a good idea to be on a WiFi channel that’s the least utilised.
Perform a Factory Reset
Among all the Linksys Velop Troubleshooting steps is the factory reset. When nothing else helps, you can follow the Linksys Velop Reset process to eliminate issues. Here’s how you can reset your Linksys Velop router:
- Locate the RESET button on the back/side panel of your router.
- Press and hold the RESET button using a pin/paperclip for about 5-6 seconds.
- Once the LED on the front starts to flash, release the button. Allow some time for the router to reboot.
- Once the router is back up and running, reconfigure the Velop settings and start using the internet again.